DC Audio 1.2k - 1,200w Monoblock Amplifier
$424.99
DC Audio
Read more
$2,529.95
The 9.0kw competition series amplifier is a 9,000 watt mono block. It is capable of running up to 18 volts
for up to 11,000 watts. It is a linkable amp and designed to run at 1 ohm per amp or 2 ohms when strapped.
It comes with a bass knob and a clipping indicator. For power inputs it will accept triple 0 awg for power and triple 0 awg for ground.
Key Features
• 1 ohm stable
• Variable low pass filter
• Variable subsonic filter
• Variable bass boost
• Wired remote control
• Triple 0 awg power and ground inputs
We recommend for installation
• 1 upgraded battery under the hood
• 3 extra 800ci battery in the rear
• Minimum of two 0 awg ran from the front battery to the rear batterys
• All 0 awg power and ground inputs on amp must have 0 awg ran to them for a total of 6 runs into the amp
• 2 upgraded aftermarket alternators
• Dash mounted voltage meter
| Features | Voltage | 9.0kw | |
| Output Power (RMS) | 4 ohm | 14.4V | 2,400W x 1 |
| 2 ohm | 4,800W x 1 | ||
| 1 ohm | 9,000W x 1 | ||
| 1 ohm | 16V | 9,800W x 1 | |
| 1 ohm | 18V | 11,000W x 1 | |
| Input Sensitivity | 6V~0.2V | ||
| Low Pass Filter | Switchable | ||
| ( @ 24 dB Slope) | Variable | Hz | 35~250 |
| Subsonic Filter | Switchable | ||
| ( @ 24dB slope ) | Variable | Hz | 10~50 |
| Bass Boost | Variable | dB | 0-9dB |
| Frequency Response | Hz | 15-270 | |
| Signal to Noise Ratio | dB | 100 | |
| Damping factor | 150< | ||
| Efficiency @ 4ohm | % | Over 90% | |
| THD @ 4ohms | Less than 0.1% | ||
| Fuse Rating | 900 Amps | ||
| Linked Fuse Rating | 1800 Amps | ||
| Indicator | Power | Yes | |
| Protection | Yes | ||
| Clip | No | ||
| Speaker & Power terminal | Mold Type | Yes | |
| Power | Gauge | 0Ga x 3 | |
| Heatsink Length | inch/mm | 34.65"/880mm |
Description
The 9.0kw competition series amplifier is a 9,000 watt mono block. It is capable of running up to 18 volts
for up to 11,000 watts. It is a linkable amp and designed to run at 1 ohm per amp or 2 ohms when strapped.
It comes with a bass knob and a clipping indicator. For power inputs it will accept triple 0 awg for power and triple 0 awg for ground.
Key Features
• 1 ohm stable
• Variable low pass filter
• Variable subsonic filter
• Variable bass boost
• Wired remote control
• Triple 0 awg power and ground inputs
We recommend for installation
• 1 upgraded battery under the hood
• 3 extra 800ci battery in the rear
• Minimum of two 0 awg ran from the front battery to the rear batterys
• All 0 awg power and ground inputs on amp must have 0 awg ran to them for a total of 6 runs into the amp
• 2 upgraded aftermarket alternators
• Dash mounted voltage meter
| Features | Voltage | 9.0kw | |
| Output Power (RMS) | 4 ohm | 14.4V | 2,400W x 1 |
| 2 ohm | 4,800W x 1 | ||
| 1 ohm | 9,000W x 1 | ||
| 1 ohm | 16V | 9,800W x 1 | |
| 1 ohm | 18V | 11,000W x 1 | |
| Input Sensitivity | 6V~0.2V | ||
| Low Pass Filter | Switchable | ||
| ( @ 24 dB Slope) | Variable | Hz | 35~250 |
| Subsonic Filter | Switchable | ||
| ( @ 24dB slope ) | Variable | Hz | 10~50 |
| Bass Boost | Variable | dB | 0-9dB |
| Frequency Response | Hz | 15-270 | |
| Signal to Noise Ratio | dB | 100 | |
| Damping factor | 150< | ||
| Efficiency @ 4ohm | % | Over 90% | |
| THD @ 4ohms | Less than 0.1% | ||
| Fuse Rating | 900 Amps | ||
| Linked Fuse Rating | 1800 Amps | ||
| Indicator | Power | Yes | |
| Protection | Yes | ||
| Clip | No | ||
| Speaker & Power terminal | Mold Type | Yes | |
| Power | Gauge | 0Ga x 3 | |
| Heatsink Length | inch/mm | 34.65"/880mm |
Reviews (0)
Be the first to write a review
Be the first to write a review
Additional info
SKU:
DCA-9K
Shipping:
Calculated at Checkout
Warranty:
LIMITED PRODUCT WARRANTY
LENGTH OF WARRANTY
DC Audio Products are covered by warranty for 1 year from date of purchase on parts and labor.
This applies to the original purchaser only. Warranties are non-transferable.
DETAILS OF WARRANTY
From the date of original purchase and for the respective period, specified above.
DC Audio agrees to repair or replace all DC Audio products, which are defective in material
and/or workmanship. This warranty is not transferable and applies only to the original purchaser of the product. No Exceptions. It is DC Audio’s right to decide if a product will be repaired or replaced.
All returns must be sent with an RA # on the outside of the box. Any and all products sent without a RA will be refused. An RA # can be obtained by calling DC Audio and requesting the number.
Warranty claims must be accompanied by the original invoice to validate the warranty service.
EXCLUSIONS
This warranty does not apply with respect to the following:
DC Audio’s warranty does not cover burned/open voice coils or lead wires,
ripped surrounds or folded cones. These are all immediate signs of abuse/over powering.
It does not cover products driven over their mechanical limits.
Defects or damage caused by accident, fire, flood, and lightning or other acts of God.
Defects or damage caused by abuse, misuse, or negligence.
Products with voice coils that have failed due to excessive power levels or clipping, i.e. burned or open coils or lead wires.
Damage caused during shipping or handling. These claims are made with the Freight Company.
Accessories or anything else attached to or to be used with DC Audio products.
Products that have their serial numbers removed or altered.
Packing materials i.e. card board boxes, foam inserts, corners, peanuts, etc.
Adjustments or alterations required for any reason.
Items subject to fatigue through normal wear and use.
Product, which has been altered or repaired by anyone other than DC Audio.
RE-CONES
All speakers, loudspeakers, subwoofers that have been re-coned by DC Audio will continue under warranty until the full 1 year warranty has expired. Any re-cone not performed at DC Audio by an authorized DC Audio worker is not covered under warranty. The end consumer accepts the responsibility and liability of knowing this speaker, loudspeaker, subwoofer no longer falls under DC Audio’s warranty program when the re-cones they purchased and/or the labor was performed by the end consumer.
Amplifiers
Amplifiers will not be covered under warranty if ran below their rated ohm load or if underpowered in any way. DC Audio has a "Recommended for Installation" section on each amplifiers web page. These need to be followed in order to ensure the amplifier will operate properly. Failure to do so can decrease the life of the amplifier and void your warranty.
